Smc-networks SMC7008ABR Manual do Utilizador

1BarricadeBroadband Router with built in4 port switch and Print serverInstallation GuideSMC7004ABR

10Netscape1. Open Netscape and click the stop button. Click “Edit,” then click“Preferences…”2. In the “Preferences” window, under “Category” double-cl

11Conguring Your Computer with Windows 2000Step 1. Congure TCP/IP SettingsAfter you have completed the hardware setup, you need to congure your com

12TCP/IP Conguration SettingIP Address ____.____.____.____Subnet Mask ____.____.____.____Primary DNS Server ________.____.____Secondary D

13Netscape1. Open Netscape and click the stop button. Click “Edit,” then click “Preferences…”2. In the “Preferences” window, under “Category” double-c

14Conguring Your Computer with Windows NT 4.0Step 1. Congure TCP/IP SettingsAfter you have completed the hardware setup, you need to congure your c

157. In the “TCP/IP Properties” dialog box, click the IP address tab to locate your IP address, subnet Mask, and default gateway. Record these values

16Step 2. Disable HTTP ProxyYou will need to verify that the “HTTP Proxy” feature of your Web browser is disabled. This is so that your Web browser wi

17Step 3. Obtain IP Settings From Your BarricadeNow that you have congured your computer to connect to your Barricade, it needs to obtain new network

18Conguring Your Macintosh ComputerYou may nd that the instructions here do not exactly match your screen. This is because these steps and screensho

194. After writing down your IP settings, select “Using DHCP Server” in the “Congure” eld and close the window.5. Another box will appear asking whe

2Table of ContentsHardware Setup 4Conguring Your Computer 6Conguring Your Computer with Windows 95/98/ME 6Conguring Yo

20Netscape1. Open Netscape and click the stop button. Click “Edit” and select“Preferences.”2. In the “Preferences” dialog box, In the left-hand column

21Conguring Your BarricadeNow that you have successfully congured your computer and retrieved your new network settings from your Barricade, you are

22Using a password can protect your Barricade from unauthorized changes. Not using a password can easily leave your Barricade-and your network-open to

23By using the Barricade’s built-in DHCP (Dynamic Host Control Protocol) server you are allowing the Barricade to handle all the IP addressing on your

24If you connect to the Internet using a Cable Modem, your ISP probably uses DHCP to issue an IP address to you. If you use a Cable Modem or you know

25Conguring Your Barricade for a Dynamic IP Address1. Select “Dynamic IP address,” and click “More Conguration.”Both options on this page for furthe

263. If you need to “Clone” the MAC Address from your network card, click “Clone MAC Address.” The MAC Address eld will display the new address.4. Cl

27Congratulations! Conguration is complete and your Barricade is now connected to the Internet. There are also some advanced conguration options tha

28Conguring Your Barricade .for a Static IP Address1. Select “Static IP address,” and click “More Conguration.”2. Enter the IP address, subnet mask,

294. Enter the DNS server address(es) in the spaces provided.5. Click “ENTER” when nished.Many ISPs use modems that provide auto-conguration. Someti

3Congratulations on your purchase of the SMC Barricade™ Broadband Router.The SMC Barricade is a Broadband Router designed to share Internet Access, pr

30Conguring Your Barricade for PPPoE1. Select “PPP over Ethernet,” and click “More Conguration.”2. Enter the User Name and Password required by your

315. If you are connecting to the Internet through PPPoE, you probably do not need to enter anything here. However, if there is another DNS server tha

32Conguring Your Barricade for Dialup on Demand1. Select “Dialup on Demand,” and click “More Conguration.”2. If the serial port is used for primary

33Conguring Your Computer for the Barricade Print ServerIf you are not connecting your printer to your Barricade, skip this section.With the Barricad

346. Insert the Installation CD into your CD-ROM drive.7. Click “Start” and “Run…”8. Type “D:\PrintSvr\Setup” and click “OK.”9. InstallShield will gui

35Step 2: Conguring SMC Barricade Print Server MonitorNow that the software is installed, it must be congured to work properly.1. Click “Start,” cli

364. From the list of manufacturers and printers in the next window, select the printer you have attached to the Barricade.5. Select the SMC Barricade

37PPtP InstallationEnter PPtP user account and password given by your Internet service provider. Service name is generaly not necessary ; but may be n

38CopyrightInformation furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for

39

4Hardware Setup1. Connecting Computers: Connect computers directly to the Barricade on ports 1-4 on the front panel. If you have more than 4 computers

40LIMITED WARRANTYLimited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its productsto be free from defects in workmanship and materials, un

41WARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE ASWARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR ORREPLACEMENT OF THE PRODUCT IN Q

42FCC - Class BThis equipment has been tested and found to comply with the limits for a Class Bdigital device, pursuant to Part 15 of the FCC Rules. T

43Safety ComplianceUnderwriters Laboratories Compliance StatementImportant! Before making connections, make sure you have the correct cord set. Check

4411. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten Sie es vom Stromnetz trennen. Somit wird im Falle einer Überspannung eine Bes

45WAN Interface 10/100BASE-T, 1 RJ-45 port Serial, 1 RS232 DB-9 connectorLAN Interface 10BASE-T/100BASE-TX 4 RJ-45 portsPrinte

46

5Indicator LEDsThe front panel of the Barricade provides indicator LEDs (Light Emitting Diodes) for easy monitoring. The following table denes the fu

6Conguring Your Computer with Windows 95/98/MEYou may nd that the instructions here do not exactly match your version of Windows. This is because th

71. From the Windows desktop, click the “Start” button. Choose “Settings,” then click “Control Panel.”2. From “Control Panel,” double-click the “Netwo

84. Select the “IP Address” tab.If “Obtain an IP address automatically” is already selected, your computer is already congured for DHCP. Click “Cance

9TCP/IP Conguration SettingIP Address ____.____.____.____Subnet Mask ____.____.____.____Primary DNS Server ____.____.____.____Secondary D