TigerAccess™ EEEthernet-over-VDSL2 CPE◆ High-speed Internet access over existing phone lines◆ Concurrent data/phone services over single connection ◆
COMPLIANCESviWarnings and Cautionary MessagesWarnings (in German)Environmental StatementThe manufacturer of this product endeavours to sustain an envi
COMPLIANCESviiManufacturing MaterialsThere are no hazardous nor ozone-depleting materials in this product.DocumentationAll printed documentation for t
COMPLIANCESviii
ixTABLE OF CONTENTS1 About the TigerAccess-EE CPE . . . . . . . . . . . . . . . . . 1-1Overview . . . . . . . . . . . . . . . . . . . . . . . . .
TABLE OF CONTENTSxGlossaryIndex
1-1CHAPTER 1ABOUT THETIGERACCESS-EE CPEOverviewThis Ethernet-Over-VDSL2 CPE system consists of an end-user CPE (Customer Premise Equipment) and a VDSL
ABOUT THE TIGERACCESS-EE CPE1-2MDF distribution equipment into the switch. The data and phone signals for each user are combined in the switch, and pa
VDSL TECHNOLOGY1-3VDSL TechnologyVDSL (Very High Bit-Rate Digital Subscriber Line) is at the high-end of all the DSL technologies, offering the best c
ABOUT THE TIGERACCESS-EE CPE1-4data rate in the downstream (receive) direction than in the upstream (transmit) direction.VDSL delivers high-performanc
SYSTEM REQUIREMENTS1-5• Supports ITU-T VDSL/VDSL2 and ANSI T1E1.4 Part 1 VDSL interface standards, as well as other evolving ETSI, ANSI, and ITU VDSL
ABOUT THE TIGERACCESS-EE CPE1-6• Power requirements: 12 VDC via the included AC power adapter. Make sure that a properly grounded power outlet is with
2-1CHAPTER 2HARDWARE DESCRIPTIONUnpackingAfter unpacking this CPE, check the contents to be that sure you have received all the components. Then, befo
HARDWARE DESCRIPTION2-2Front and Rear PanelThis device is an external VDSL2 CPE for high-speed Internet access applications. The front panel of the CP
SYSTEM AND PORT STATUS LEDS2-3System and Port Status LEDsThe CPE includes key system and port indications that simplify installation and network troub
HARDWARE DESCRIPTION2-4
3-1CHAPTER 3INSTALLATIONInstallation OverviewBefore installing the CPE, verify that you have all the items listed in the “Unpacking” on page 2-1. If a
INSTALLATION3-21. Using standard telephone cable, connect the CPE’s RJ-11 LINE port to the RJ-11 telephone wall jack providing the VDSL service.2. Con
CONFIGURING THE TCP/IP PROTOCOLS3-3Configuring the TCP/IP ProtocolsTo connect the CPE to a computer through its Ethernet port, the computer must have
INSTALLATION3-4Windows XP1. Click “Start/Control Panel/Network Connections.”2. Right-click the “Local Area Connection” icon for the adapter you want t
A-1APPENDIX ATROUBLESHOOTINGDiagnosing CPE IndicatorsCPE operation is easily monitored via the LED indicators to identify problems. The table below de
20 Mason,Irvine, CA 92618Phone: (949) 679-8000TigerAccess-EE CPEInstallation GuideFrom SMC’s Tiger line of feature-rich workgroup LAN solutionsFebruar
TROUBLESHOOTINGA-2If You Cannot Connect to the Internet• Check that your computer is properly configured for TCP/IP. See “Configuring the TCP/IP Proto
B-1APPENDIX BCABLESTwisted-Pair Cable and Pin AssignmentsFor 10BASE-T and 100BASE-TX connections, the twisted-pair cable must have two pairs of wires.
CABLESB-210BASE-T/100BASE-TX Pin AssignmentsUse unshielded twisted-pair (UTP) or shielded twisted-pair (STP) cable for RJ-45 connections: 100-ohm Cate
TWISTED-PAIR CABLE AND PIN ASSIGNMENTSB-3Straight-Through WiringIf twisted-pair cable is to join two ports and only one of the ports has an internal c
CABLESB-4Crossover Wiring If the twisted-pair cable is to join two ports and either both ports are labeled with an “X” (MDI-X) or neither port is labe
RJ-11 PORTSB-5RJ-11 PortsStandard telephone RJ-11 connectors and cabling can be found in several common wiring patterns. These six-pin connectors can
CABLESB-6Table B-2 RJ-11 Port PinoutsPinSignal Name Wire Color1Not used2 Line 2 Tip Black or White/Orange3 Line 1 Ring Red or Blue/White4 Line 1 Tip
C-1APPENDIX CSPECIFICATIONSVDSL Functional CriteriaBand Plan: Up to 6 bandsSignal Bandwidth: 25 kHz to 30MHzOptional Band: US0 operating at 4~25 kHz (
SPECIFICATIONSC-2Power Consumption7 Watts maximumInput Power12 VDC (via AC power adapter), 1 A maximumTypical 700 mA maximumSize15.5 x 12.85 x 2.8 cm
COMPLIANCESC-3CompliancesCE MarkEmissionsFCC Class BFCC Part 68Industry Canada Class BEN55022 (CISPR 22) Class BEN 61000-3-2/3CNS 13438 Class BImmunit
Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, n
SPECIFICATIONSC-4
Glossary-1GLOSSARY10BASE-TIEEE 802.3 specification for 10 Mbps Ethernet over two pairs of Category 3, 4, or 5 UTP cable.100BASE-TXIEEE 802.3u specific
GLOSSARYGlossary-2EthernetA network communication system developed and standardized by DEC, Intel, and Xerox, using baseband transmission, CSMA/CD acc
GLOSSARYGlossary-3Local Area Network (LAN) A group of interconnected computer and support devices.Media Access Control (MAC)A portion of the networkin
GLOSSARYGlossary-4Transmission Control Protocol/Internet Protocol (TCP/IP)Protocol suite that includes TCP as the primary transport protocol, and IP a
Index-1Numerics10BASE-T/100BASE-TX pin assignments B-2Ccablecrossover B-4straight-through B-3testing category 5 cable B-4cable connections 3-1complian
INDEXIndex-2
20 MasonIrvine, CA 92618Phone: (949) 679-8000Model Numbers: SMC7800A/VCPPub. Number: 150200004100H E022007/ST-R01FOR TECHNICAL SUPPORT, CALL:From U.S.
iLIMITED WARRANTYLimited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship and materials, un
iiWARRANTIES EXCLUSIVE: IF AN SMC PRODUCT DOES NOT OPERATE AS WARRANTED ABOVE, CUSTOMER’S SOLE REMEDY SHALL BE REPAIR OR REPLACEMENT OF THE PRODUCT IN
iiiCOMPLIANCESFCC - Class BThis device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device m
COMPLIANCESivIf your equipment causes harm to the telephone network, the telephone company may discontinue your service temporarily. If possible, they
COMPLIANCESvWarning: Do not plug a phone jack connector in the RJ-45 port. This may damage this device. Attention: Les raccordeurs ne sont pas utilisé
Comentários a estes Manuais